- #LANDISK FIRMWARE UPDATE UPDATE#
- #LANDISK FIRMWARE UPDATE SOFTWARE#
- #LANDISK FIRMWARE UPDATE PASSWORD#
#LANDISK FIRMWARE UPDATE PASSWORD#
Remove user’s share folder completely - This will remove all files and folders of user’s completely without any backup.Īdd a new user: Type in the username, password we want. There are two options to choose in here： Leave user’s share folder for Administrator (read/write) - This option will move the user’s folder into administrator’s folder, and only read/writeable for administrator (administrator’s folder will be created automatically at the time of LAN Disk hard disk is created). We can delete the useless user’s account from here. Mobile LAN Disk User Guide 3.2.4 Users A LAN Disk hard disk MUST be installed for this function to work in properly.Ĭhange Password: We can change the user’s password from here (only works if there’s a user exist). NOTE: The printer is various in style, therefore the printer function does not guarantee to support all printers. The FTP Username and password of admin are, Username: admin, Password: admin 3.2.3 USB The installed USB hard disk, Flash disk, and USB printer will show in here. (The selection for the date and time will be close after NTP is enabled) We’re allowed to use the FTP to access to the device after enabled too. Including “Device Name”, “Description”, “Date”, “Time Zone”, “Http Port” and the NTP, FTP server can be enabling or disable in here too.Īfter the NTP option is enabled, you’ll need to enter a valid NTP server to make it work correctly. The basic settings of LAN Disk can be set at here. If you need assistance in manually entering the above information, contact your network administrator for additional help in configuring the network settings. IP Address – Enter the static IP address Subnet Mask – Enter the Subnet Mask address Default Gateway – Enter the Gateway IP address DNS1 and DNS2 (both optional) – If available, enter those IP addresses here 3.2.1.2 Static IPĬlick this option if there is no DHCP Server present on the network and manually enter the network settings in the fields provided below this option. Will fall back to the default IP address of 192.168.16.1. If DHCP Client is enabled, but there is no DHCP server, the LAN Disk Selecting this option enables the LAN Disk to request an IP and auto-configure itself to the network if there is a DHCP Server present. We can choose between DHCP and Static IP from the “Protocol” Depending on how the network is set up, changes to this page may or may not be necessary. This section contains all LAN settings to configure the LAN Disk to the network. The default username is "admin" and password is "root". 3.1 Home The basic information of the LAN Disk will be shown at here.ģ.2 Administration The username and password will be required when entering this section. Just simply type in the LAN Disk IP (default IP：192.168.16.1) in the browser to enter the LAN Disk web. At 25。C，After 5~10minutes rotating (Fan alone) 7. STEP 3： Booting up will cost about 30 seconds. STEP 2： Connect the power to LAN Disk and press the power button. STEP 1： Connect the network cable to LAN port of LAN Disk. Mobile LAN Disk User Guide 2.2.2 Installation steps of LAN Disk STEP 6： Screw the back panel to the enclosure. STEP 5： Reassemble two faceplates back to the enclosure and screw them together. Mobile LAN Disk User Guide STEP 4： Screw HDD to the enclosure. STEP 3： Place HDD into the enclosure properly connect HDD to the SATA connector. Connect LAN Disk to a switch/hub port to connect your network.Ģ.2 HW Installation 2.2.1 HDD Installation Guide TCP/IP Protocol must be installed in your PC. Installation 2.1 Requirements The following are required when using the LAN Disk. IP will be returned to factory default as 192.168.16.1 1 second (excluding other setting) 10 seconds - IP and all settings will be returned to factory defaults 1.4 LEDs BlueĪbout the 3.5” SATA Mobile LAN Disk 1.5 Front ViewĢ.
STEP2： Power On and wait for 30 seconds to get LAN Disk bootup ready. Hardware Overview 1.1 Power Receptor for the provided Power Adapter (12V DC, Maximum 2 Amps, 100-240V AC, 50-60Hz) 1.2 Ports LAN Portġ.3 Reset Button (locate on PCB) STEP1： Remove HDD. The SanDisk MP3 Updater is a standalone application designed to deliver the latest firmware for your SanDisk MP3 player.Hardware.
#LANDISK FIRMWARE UPDATE UPDATE#
For optimal experience with your SanDisk MP3 player, SanDisk recommends that you update your firmware with each new release. SanDisk actively and periodically updates the capabilities, functionality, and reliability of your SanDisk MP3 player through this firmware.
#LANDISK FIRMWARE UPDATE SOFTWARE#
Firmware is the software code that powers your SanDisk MP3 player.
0 kommentar(er)
